camInstructor Video Blog

Mastercam X9 vs Mastercam 2020

6/26/19 6:00 AM / by camInstructor Mike posted in Mastercam Dynamic Milling, Mastercam, Mill, Mastercam 2020, Mastercam X9

1 Comment

This video takes a look at the new Mastercam 2020 and compares it to an older version, Mastercam X9. Mastercam X9 is still a popular release since it was the last version on the old interface. This video looks at some of the new chaining options in 2020 and compares them against X9.

Read More

Mastercam X3 vs Mastercam 2020

6/12/19 6:00 AM / by camInstructor Mike posted in Mastercam Dynamic Milling, Mastercam, Mill, Mastercam 2020, Mastercam X3

8 Comments

This video takes a look at the new Mastercam 2020 and compares it to an older version, Mastercam X3. Mastercam X3 was released in 2008 so it's not a fair comparison but a fun look at how far things have come in the last 11 years.

Read More

Mastercam Dynamic Milling - Chaining Part 4

5/29/19 6:00 AM / by camInstructor Mike posted in Mastercam Dynamic Milling, Mastercam 2019, Mastercam, Mill

0 Comments

This is video four of five on chaining in Mastercams Highspeed Dynamic Toolpaths. This is taken from our online Highspeed Toolpath course which covers all aspects of the 2D Highspeed Toolpaths.

Read More

Mastercam - Chip Thinning RCTF and Iscar HEM

5/15/19 6:00 AM / by camInstructor Mike posted in Mastercam 2019, Mastercam, Mill

0 Comments

This is video explains Chip Thinning (RCTF) and Iscars HEM found in Mastercams Dynamic toolpaths.

Read More

Mastercam - 5 Minute 5 Axis Impeller Challenge

5/1/19 6:00 AM / by camInstructor Mike posted in Mastercam 2019, Mastercam, Mill, Impeller

5 Comments

This video runs through the programming of a 5 axis impeller in 5 minutes...the 5 minute, 5 axis, impeller challenge!

Read More

Mastercam Dynamic Milling - Chaining Part 3

4/17/19 6:00 AM / by camInstructor Mike posted in Mastercam Dynamic Milling, Mastercam 2019, Mastercam, Mill

3 Comments

This is video three of five on chaining in Mastercams Highspeed Dynamic Toolpaths. This is taken from our online Highspeed Toolpath course which covers all aspects of the 2D Highspeed Toolpaths.

Read More

Mastercam Dynamic Milling - Chaining Part 2

4/3/19 6:00 AM / by camInstructor Mike posted in Mastercam Dynamic Milling, Mastercam 2019, Mastercam, Mill

1 Comment

This is video two of five on chaining in Mastercams Highspeed Dynamic Toolpaths. This is taken from our online Highspeed Toolpath course which covers all aspects of the 2D Highspeed Toolpaths.

Read More

Mastercam Dynamic Milling - Chaining Part 1

3/20/19 6:00 AM / by camInstructor Mike posted in Mastercam Dynamic Milling, Mastercam 2019, Mastercam, Mill

3 Comments

This is video one in a series of videos covering the chaining options and strategies used in the 2D Highspeed toolpaths. These strategies differ from those used in the conventional 2D toolpaths.

Read More

Mastercam Tips - Pocket Entry Motion

3/6/19 8:56 AM / by camInstructor Mike posted in Mastercam 2019, Mastercam, Mill

3 Comments

Mastercams Pocket Entry Motion settings  may need adjusting when trying to enter small pockets or features.

Read More

Macro B Programming - Introduction

2/20/19 6:00 AM / by camInstructor Mike posted in CNC, Setup Operate, Macro

10 Comments

Macro B Programming doesn't have to be scary! Here's a brief introduction into some of the capabilities of Macro B Programming.

Read More

Mastercam Lathe Stock Recognition

2/6/19 6:00 AM / by camInstructor Mike posted in Mastercam 2019, Mastercam, Lathe

5 Comments

This video shows the use of Stock Recognition in the Lathe environment for Mastercam.

Read More

Haas CNC Lathe Setup and Operate

1/24/19 6:00 AM / by camInstructor Mike posted in CNC, Setup Operate, Haas

3 Comments

This video is taken from our Haas CNC Lathe Setup and Operate course which provides comprehensive step by step instructions for setting up and running your Haas CNC lathe.

Read More

Mastercam Entity Selection

1/9/19 6:00 AM / by camInstructor Mike posted in Mastercam Tips, Mastercam

4 Comments

This video discusses Entity Selection in Mastercam along with some options to help speed up the selection process.

Read More

Delete Duplicates in Mastercam

12/19/18 5:00 AM / by camInstructor Mike posted in Mastercam Tips, Mastercam

1 Comment

This video discusses the Delete Duplicates Function and FindOverlap CHook in Mastercam, which can be used to clean up geometry in your file.

Read More

The Different Backplot Interfaces in Mastercam

12/5/18 5:00 AM / by camInstructor Mike posted in Mastercam Tips, Mastercam

1 Comment

Did you know there are 2 different interfaces for Backplotting your toolpaths in Mastercam?

Read More

Chaining Direction Control in Mastercam

11/21/18 5:00 AM / by camInstructor Mike posted in Mastercam Tips

2 Comments

This video is taken from a QnA session during one of our Teacher Training Courses and here we're looking at how to control the direction of your chain when creating toolpaths.

Read More

Dynamic Toolpath Tool Engagement

11/8/18 6:01 AM / by camInstructor Mike posted in Mastercam 2019

2 Comments

Here I go over the Dynamic Tool Engagement & Stepover Lesson that camInstructor is offering for FREE!

Read More

New in Mastercam 2019 - Lathe Cross Center Turning

10/16/18 8:00 PM / by camInstructor Mike posted in Mastercam 2019

2 Comments

Having a look at the improved Cross Center Turning feature in Mastercam Lathe 2019.

Read More

Mastercam 2019 Interface

10/11/18 5:14 PM / by camInstructor Matt posted in Mastercam Tips

0 Comments

Taking a look at the basics of the Mastercam 2019 User Interface.

Read More

New in Mastercam 2019 - Deburr Part 2

9/26/18 7:37 AM / by camInstructor Mike posted in Mastercam 2019

0 Comments

Having a look at the new Deburr Toolpath in Mastercam 2019. Part 2 of 2.

Read More

New in Mastercam 2019 - Deburr Part 1

9/12/18 7:31 AM / by camInstructor Mike posted in Mastercam 2019

5 Comments

Having a look at the new Deburr Toolpath in Mastercam 2019. Part 1 of 2.

Read More

The New Mastercam Drill Interface

8/29/18 6:00 AM / by camInstructor Mike posted in Mastercam 2019, Mastercam, drill

2 Comments

Here I take a look at the new Drilling interface in Mastercam.

Read More

New in Mastercam 2019 - Divide

8/15/18 6:00 AM / by camInstructor Mike posted in Mastercam 2019

2 Comments

This video describes the new Divide feature in Mastercam 2019.

Read More

New in Mastercam 2019 - Advanced Display

7/25/18 6:00 AM / by camInstructor Mike posted in Mastercam 2019

2 Comments

This video describes the new Advanced Display feature in Mastercam 2019.

Read More

New in Mastercam 2019 - Model Chamfer 2

7/11/18 12:00 AM / by camInstructor Mike posted in Mastercam 2019

2 Comments

This is video 2 of 2 and describes the new Model Chamfer features in Mastercam 2019.

Read More

New in Mastercam 2019 - Model Chamfer 1

6/27/18 12:00 AM / by camInstructor Mike posted in Mastercam 2019

1 Comment

This is video1 of 2 and describes the new Model Chamfer features in Mastercam 2019.

Read More

New in Mastercam 2019 - Overview

6/20/18 12:00 AM / by camInstructor Mike posted in Mastercam 2019

1 Comment

This video describes some of the new Features in Mastercam 2019. Stay tuned for follow up videos highlighting each new feature in more detail.

Read More

Mastercam OptiRough Toolpath 4

5/31/18 6:09 AM / by camInstructor Mike posted in Mastercam Dynamic Milling

2 Comments

The 4th and final Video showing how to create more efficient toolpaths using Mastercam OptiRough Toolpath.

Read More

Mastercam OptiRough Toolpath 3

5/29/18 12:02 PM / by camInstructor Mike posted in Mastercam Dynamic Milling

1 Comment

The 3rd Video showing how to create more efficient toolpaths using Mastercam OptiRough Toolpath.

Read More

Mastercam OptiRough Toolpath 2

4/30/18 12:00 AM / by camInstructor Mike posted in Mastercam Dynamic Milling

4 Comments

Part 2 in this series looking at Mastercams 3D OptiRough toolpath.

Read More

Mastercam OptiRough Toolpath 1

4/19/18 12:00 AM / by camInstructor Mike posted in Mastercam Dynamic Milling

5 Comments

 Learn how to create more efficient toolpaths using Mastercam's OptiRough Toolpath.

Read More

Mastercam Cutter Compensation

3/1/18 5:42 PM / by camInstructor Mike posted in Mastercam Tips

2 Comments

Having a look at the different types of Cutter Compensation you can use in Mastercam.

Read More

Mastercam Linking Parameters - Top of Stock and Depth

12/12/17 5:46 PM / by camInstructor Mike posted in Mastercam Linking Parameters

1 Comment

Looking at the Linking Parameters page, learn to utilize Mastercam's Top of Stock and Depth settings.

Read More

Mastercam Linking Parameters - Feed Plane

11/15/17 5:43 PM / by camInstructor Mike posted in Mastercam Linking Parameters

0 Comments

Looking at the Linking Parameters page, learn to utilize Mastercam's Feed Plane settings.

Read More

Mastercam Linking Parameters - Retract

10/10/17 11:04 AM / by camInstructor Mike posted in Mastercam Linking Parameters

2 Comments

Looking at the Linking Parameters page, learn how to utilize Mastercam's Retract Settings.

Read More

Mastercam Linking Parameters - Clearance

9/18/17 11:07 AM / by camInstructor Mike posted in Mastercam Linking Parameters

1 Comment

Looking at the Linking Parameters page, learn how to utilize Mastercam's Clearance Settings

Read More

Mastercam Dynamic Milling Part 5

4/28/17 10:45 AM / by camInstructor Mike posted in Mastercam Dynamic Milling

0 Comments

This video series covers every setting in Mastercams Dynamic Milling Toolpath. This is Part 5 of 5.

Read More

Mastercam Dynamic Milling Part 4

3/28/17 10:51 AM / by camInstructor Mike posted in Mastercam Dynamic Milling

0 Comments

This video series covers every setting in Mastercams Dynamic Milling Toolpath. This is Part 4 of 5.

Read More

Mastercam Dynamic Milling Part 3

2/27/17 1:27 AM / by camInstructor Mike posted in Mastercam Dynamic Milling

0 Comments

This video series covers every setting in Mastercams Dynamic Milling Toolpath. This is Part 3 of 5.

Read More

Mastercam Dynamic Milling Part 2

1/27/17 10:56 AM / by camInstructor Mike posted in Mastercam Dynamic Milling

0 Comments

This video series covers every setting in Mastercams Dynamic Milling Toolpath. This is Part 2 of 5

Read More

Mastercam Dynamic Milling Part 1

1/2/17 11:00 AM / by camInstructor Mike posted in Mastercam Dynamic Milling

0 Comments

This video series covers every setting in Mastercams Dynamic Milling Toolpath. This is Part 1 of 5.

Read More

Subscribe to Email Updates

New call-to-action

    Recent Posts